O ring factory manufacturer by dmsseals.com: The Primary Seal – While two of the sealing points in a seal design are simple static seals, the seal between the rotating and stationary members needs a little more consideration. This primary seal is the basis of all seal design and is essential to its effectiveness. The primary seal is essentially a spring loaded vertical bearing – consisting of two extremely flat faces, one fixed, one rotating, running against each other. The seal faces are pushed together using a combination of hydraulic force from the sealed fluid and spring force from the seal design. In this way a seal is formed to prevent process leaking between the rotating (shaft) and stationary areas of the pump. The surfaces of the seal faces are super-lapped to a high degree of flatness; typically 2-3 Helium light-bands (0.00003” / 0.0008mm). If the seal faces rotated against each other without some form of lubrication they would wear and quickly fail due to face friction and heat generation. For this reason some form of lubrication is required between the rotary and stationary seal face; this is known as the fluid film. Find more information on https://www.dmsseals.com/scraper-seals.
Types of Mechanical Seals – Several types of mechanical seals are available. Some of the popular ones include: Balanced and unbalanced seals; Pusher and non-pusher seals Cartridge seals. A mechanical seal consists of rotary and stationary faces running against each other. These faces apply a closing force against each other using springs and the pressure generated from the process fluid. This way, a seal is formed to prevent the fluid from leaking between the rotating shaft and the pump housing. Mechanical seals can be selected based on the type of pump application. Choosing the wrong seal can affect pump performance and lead to damage and costly repairs. An unbalanced mechanical seal is preferred if the pump needs to operate at a lower pressure. However, high pressure pumping applications require balanced mechanical seals. Balanced seals also perform better in high temperature operating conditions. Cartridge seals require less maintenance but are more expensive, hence used for limited applications.
Key points of engineering mechanical seal design: Select a reasonable sealing scheme, focusing on the above requirements. First of all, the dustproof performance must be good. More than 80% of the failures of the hydraulic system are directly or indirectly derived from the stains in the system. Choose the best seals For seals of the same structure, the product quality of each company varies greatly. On the whole, the quality of large foreign seal companies is relatively stable, but the probability of encountering fakes is too high. Sometimes the so-called direct supply is not reliable. In terms of domestic seals, most of them are not very good, but at present, some manufacturers’ products have been chasing or even surpassing imported products, with stable and reliable quality, such as tetrafluoroethylene and rubber seals produced by Damson Sealing.
The O-ring seal, which is also called shaft seal, is noted for a reasonable compression and stretch rate to achieve a good sealing effect. It will not leak when it is sealed statically. At the same time, the O-ring size is properly matched to the groove size. The structure is simple and its installation is very close to the machine. Its most prominent advantage is its self-sealing effect, eliminating the need for periodic adjustments. We guarantee that the size and mounting grooves of all our O-rings are standardized, so they are cost-effective and easy to maintain. They have low frictional resistance and are suitable for occasions where the pressure is often alternating.
Sealing performance over conventional O-rings is achieved by reducing particle generation, extending seal life and minimizing replacement time during preventive maintenance. Compared to traditional O-rings, this seal effectively reduces the number of dust particles generated during operation and extends the life of the machine with bonded seals installed. The seal has a working diameter range of 6.5 to 60.58mm.
The rod seals can be operated with or without lubrication. We guarantee strong dimensional stability and a low coefficient of friction. Changes in temperature do not affect its performance. It is easy to install and can be used with piston rods with the larger diameter and heavy-duty hydraulic rod sealing systems to provide a tight and excellent seal. DMS Seals with 12+ years of experience for manufacturing rod seals, we are confident to provide top quality & satisfying product. There are hydraulic rod seals, piston rod seals, etc for selection, welcome to contact us for further details.
Gasket sealing mechanism: The function of the gasket is caused by the blocking effect on the internal medium formed by the contact pressure of the sealing material on the joint surface and the elastic restoring force to the external tightening force. Classification and structure of gaskets: Gaskets are divided into three categories: non-metallic gaskets, non-metallic and metal combined gaskets and metal gaskets. The common materials are rubber, leather, asbestos board, cork, PTFE, tinplate, steel, aluminum, copper and stainless steel.
DMS SEALS is a technology enterprise which specialized in the production of seals, the development of seals material and the solution of the sealing of special working condition. We own 120 staffs which including 70 middle and senior technicians. Our factory covers more than 10000 square meters which including 8000 square meters for the workshop. Our production equipment and test equipment are on leading level in the same industry. We are the one of the biggest enterprise who specialized in manufacturing and developing seals in China. We have long time cooperation and communication with many universities and research institutions at home and board. See additional details at https://www.dmsseals.com/.
DMS Seals is a scientific and technical mechanical seal manufacturer and oil seal supplier specializing in seal production, sealing material development, and the conception of sealing solutions for special working conditions. We have 120 employees, including 70 senior technicians. DMS Seals has a number of invention patents and leading production processes. The R&D team is able to design and develop Rubber Seal & Hydraulic Seals for various mechanical sealing systems under complex conditions. We have already passed the certification of ISO 9001 and TS 16949.
Bobby Marino